Zonal Statistics as Table (Spatial Analyst)
Summary
Summarizes the values of a raster within the zones of another dataset and reports the results to a table.
Illustration
 |
ZonalStatisticsAsTable(ZoneRas, "Value", ValRas, OutTable, "ALL") |
Usage
-
A zone is defined as all areas in the input that have the same value. The areas do not have to be contiguous. Both raster and feature datasets can be used for the zone input.
When the zone and value inputs are both rasters of the same resolution, they will be used directly.
If the resolutions are different, an internal resampling is applied to make them match before the zonal operation is performed.
Should there be any NoData cells in the inputs, the resampling may cause there to be larger areas of NoData in your output than you might have expected. To avoid this situation, either Resample the coarser input rasters to the resolution of the finer input raster, or set the Cell size to Minimum Of Inputs in the Raster Analysis environment.
If the zone input is a raster dataset, it must have an attribute table. The attribute table is usually created automatically for integer rasters, but may not be under certain circumstances. You can use Build Raster Attribute Table to create one.
If the zone input is a feature dataset, a vector-to-raster conversion will be internally applied to it. To ensure that the results of the conversion will align properly with the value raster, it is recommended that you check that the extent and snap raster are set appropriately in the environment settings and the raster settings.
Since the internal raster must have an attribute table, an error will occur if one was not created in the conversion. If this happens, convert your feature dataset directly with Feature To Raster, Polygon To Raster, Point To Raster, or Polyline To Raster. Generate an attribute table for it as described in the previous tip and use the resulting raster as your Zone input.
If the zone input is a feature dataset with relatively small features, keep in mind that the resolution of the information needs to be appropriate relative to the resolution of the value raster. If the areas of single features are similar to or smaller than the area of single cells in the value raster, in the feature-to-raster conversion some of these zones may not be represented.
To demonstrate this, try converting the feature dataset to a raster with the appropriate feature-to-raster conversion tool and specify the resolution to be that of the Value raster. The result from this conversion will give an indication about what the default output of the zonal operation will be.
If you have fewer results in the output than you may have expected, you need to determine an appropriate raster resolution that will represent the detail of your feature input, and use this resolution as the Cell Size of the Raster Analysis Settings of the Environment.
If the zone input is a point feature dataset, it is possible to have more than one point contained within any particular cell of the value input raster. For such cells, the zone value is determined by the point with the highest feature ID.
If the zone feature input has overlapping polygons, the zonal analysis will not be performed for each individual polygon. Since the feature input is converted to a raster, each location can only have one value.
An alternative method is to process the zonal statistics iteratively for each of the polygon zones and collate the results.
It is recommended to only use rasters as the zone input, as it offers you greater control over the vector-to-raster conversion. This will help ensure you consistently get the expected results.
When specifying the input zone data, the default zone field will be the first available valid field. If no other valid fields exist, the ObjectID field (for example, OID or FID) will be the default.
If a reserved field (for example, OBECTID, FID, or OID) is selected for the Zone field, then this may cause some ambiguity in the result. The result includes the particular reserved field name necessary for the particular output format type, as well as the Zone field specified. If the specified field has the same name as the reserved field for the particular output format, in the output the name for the zone field will be altered in such a way that all field names in the result are unique.
Note:To make a field of unique values that does not have a reserved name, use the Add Field and Calculate Field geoprocessing tools.
The input value raster can be either integer or floating point. However, when it is floating-point type, the zonal calculations for majority, median, minority, and variety will not be computed.
For majority and minority calculations, when there is a tie, the output for the zone is based on the lowest of the tied values.
-
A field or series of fields will be created in the output table, depending on the setting of the Statistics type. When the Value input is integer, all of the statistics (Area, Min, Max, Range, Mean, STD, Sum, Variety, Majority, Minority, and Median) are available to be calculated. If the Value input is floating point, the Majority, Minority, Median, and Variety statistics will not be calculated.
-
The data type for each value under the items in the output table is dependent on the zonal calculation being performed. See how Zonal Statistics works for the specific behavior of any statistic.
-
The number of rows in the output table is the number of zones.
Syntax
| Parameter | Explanation | Data Type |
in_zone_data |
Dataset that defines the zones. The zones can be defined by an integer raster or a feature layer. | Raster Layer | Feature Layer |
zone_field | Field that holds the values that define each zone. It can be an integer or a string field of the zone dataset. | Field |
in_value_raster |
Raster that contains the values on which to calculate a statistic. | Raster Layer |
out_table |
Output table that will contain the summary of the values in each zone. | Table |
ignore_nodata (Optional) |
Denotes whether NoData values in the Value input will influence the results of the zone that they fall within.
| Boolean |
statistics_type (Optional) |
Statistic type to be calculated.
| String |
Code Sample
This example summarizes the values of a raster within the zones defined by a polygon shapefile and records the results in a table.
import arcpy
from arcpy import env
from arcpy.sa import *
env.workspace = "C:/sapyexamples/data"
outZSaT = ZonalStatisticsAsTable("zones.shp", "Classes", "valueforzone",
"zonalstattblout", "NODATA", "SUM")
This example summarizes the values of a raster within the zones defined by a polygon shapefile and records the results in a .dbf file.
# Name: ZonalStatisticsAsTable_Ex_02.py
# Description: Summarizes values of a raster within the zones of
# another dataset and reports the results to a table.
# Requirements: Spatial Analyst Extension
# Import system modules
import arcpy
from arcpy import env
from arcpy.sa import *
# Set environment settings
env.workspace = "C:/sapyexamples/data"
# Set local variables
inZoneData = "zones.shp"
zoneField = "Classes"
inValueRaster = "valueforzone"
outTable = "zonalstattblout02.dbf"
# Check out the ArcGIS Spatial Analyst extension license
arcpy.CheckOutExtension("Spatial")
# Execute ZonalStatisticsAsTable
outZSaT = ZonalStatisticsAsTable(inZoneData, zoneField, inValueRaster,
outTable, "NODATA", "MEAN")